buy online | Tools
Specifications:- Color: red- Size: 58*44*13mm- Accuracy: 30/2mm
Hex 2.5 MM Long Driver Ideal for X 650 Maintenance
The all new Turnigy temp checker now handles temp up to 356F! making it also reat for hot glow/gas engines!Our Turnigy Infrared Thermometer can check the temperature of any Motor, ESC or battery simply by pointing and pressing the button. There is no need to make contact with the object!An excellent way to check battery or motor temps!Specifications.Measuring Range : -33~180C (-27.4~356F)Operating Range : 0~50C (32~122F)Full Range Accuracy : +/- 2.5C, 2.5%Distance :2~40cmEmissivity Range : 0.95 fixedWave Length : 5um~14um Power Supply : LR44X2
Great for checking all your Props are spinning at equal RPM comes with Button Battery IncludedEver wanted to know how fast your motor is spinning?Wished you could better select the right propeller for your motor?Now you can more accurately tune and performance test your engine, motor, edf or heli with the Turnigy tachometer.Measures 2 to 9 propellers.Super easy to use.0-99999rpm rangeFeatures: Ultra sharp backlit LCD220mah Lion battery includedAuto shut-off when idle. (no more flat batteries)Weighs only 39g
Designed to fit nearly all transmitter antenna positions and allow for a neck-strap, the new TURNIGY transmitter glove is a must have item for low temperature flying conditions.ade with a heavyweight zip, durable transparent cover that wont get brittle in sub zero temperatures and padded cotton/nylon material to insulate and protect against wind, snow and light rain.You now have one less excuse to avoid getting outside and flying your model aircraft.Spec.Maximum transmitter size: 270x270mm
Universal Heater System features temperature adjustment and a thermal sensor to allow temperature control from 30 to 80 degrees celcious. With a voltage range of 7.4v to 12v the heater can be powered by a 2s to 3s lipo. Add one to your transmitter glove and fly in luxury this winter, warm the tyres on your car or pre-heat your lipo in winter or even summer for the best performance.Pre-heating a Lipo pack to 30degC in winter will give your model much better performance, right from the start.Specs:Input: 7.4v to 12vTemperature: 30~80deg CelciousSensor: LM35DZ - Precision Centigrade Temperature Sensor Heat Pads: 310x80mmAmp Draw: 5.2A @ 12vInput Connector: 2 x Alligator Clips Picture of heater pads 2 x pads
5 Minute Quality Epoxy Glue5 Minute Quality Epoxy GlueMinute A/B Epoxy Glue.A very high quality clear setting epoxy glue.Excellent gap filling and bonding properties on almost all surfaces including delicate foam and hard to bond alloy.Product comes in sealed air-tight packaging.You wont find a better quality epoxy from China. In fact, its possible to find 20cent epoxy glues of the same size, however they dont dry clear and their holding strength and adhesion is very poor.Our glue is produced by MIRA, one of Chinas leading glue manufacturers who supply glues to Chinas aerospace and civil engineering market, requiring strict quality and performance guidlines.Save yourself the headache and only purchase quality glues.An essential item for any building project and perfect for emergency in-field repairs
Maxi-Cure Extra Thick CA 1. ozMaxi-Cure Extra Thick CA 1. ozMAXI-CUREâ¢ extra thick CA is the best CA for most plastics, including GEâs Lexan MAXI-CUREâ¢ is the best choice for plastic model assembly. When used with INSTA-SETâ¢, it works better than any putty for modifying or filling voids. It can be carved with a knife or razor blade and sanded and feathered to form a finish indistinguishable from plastic.MAXI-CUREâ¢ bonds fiberglass, hardwood, metal and rubber better than any other hobby adhesive. For gluing to the inside, clothtextured surface of fiberglass, scrape the area to be bonded with a razor blade or coarse sandpaper before using MAXI-CUREâ¢ or any other adhesive. It also is best for bonding the tires for R/C cars.
Insta-Flex Plus Clear Rubber CA 1. ozINSTA-FLEX+â¢ clear rubber toughened has similar qualities to our black IC-2000â¢ but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000â¢ that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX+â¢ has this carbon removed, its strength is a little less than IC-2000â¢ but still superior to standard CAs. When esthetics are important and a flexible bond is required, INSTA-FLEX+â¢ is your best choice. It forms superior bonds to soft urethane and vinyl plastics. Both INSTA-FLEXâ¢ and INSTA-FLEX+â¢ work well when bonding R/C car tires. When a joint has a larger than normal gap, flexible CAs provide superior shock resistent bonds.
Insta-Cure Super Thin CA 1/2 ozINSTA-CUREhas a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the seam. At the moment CAs cure, they give off a vapor that can irritate the nose and eyes, so be prepared. Thin CAs work very well on balsa since they penetrate into the wood and form more than just a surface bond.INSTA-CURE is a highly refined CA which, combined with its freshness, gives a guaranteed 2 year shelf life.
Insta-Cure Plus Gap Filling CA 1/2 ozInsta-Cure Plus Gap Filling CA 1/2 oz INSTA-CURE+â¢ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface areas, including those with close fitting joints such as laminations, INSTA-CURE+ â¢ should also be used. To prevent premature curing, donât spread the glue into a thin film. Lay down a serpentine bead with about 1" separations on one surface, then assemble the parts, letting the pressure spread the CA out.
Finish-Cure 20 Min Epoxy 4.5 ozFINISH-CURE 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE can be sanded the easiest of all our epoxies and is excellent for the sheeting of foam core wings. Allow 8 hours for full curing. For best results, FINISH-CURE should be heated to a temperature above 85 degrees F or applying light weight fiberglass, lay cloth on balsa first, then brush on FINISH-CURE. When fully saturated, go over the surface with a heat gun, and then squeegee off excess epoxy with a playing card from an old deck. Heat and remove excess several times for a light weight finish. If room temperature is below 70 degrees F use a heat gun on the surface several times for the next 2 hours. When dry, lightly sand, then fill surface with a low weight spakeling compound, scrapping off excess with a playing card. Sand to a smooth finish ready for primer. For heavy weight fiberglass, apply the epoxy before and after laying down the cloth. FINISH-CURE is best mixed in a disposable cup.
1kg Range Accuracy 0.1gPower On Self Test, Automatic shutdown, overload TipsAuto-zero tracking, self-blue LEDIn addition to skin, set the zero functionFourth gear unit conversion: g / oz / ozt / dwtPower Supply: 3VProduct Dimensions: 115 * 61 * 19Display Box Size: 25mmWeighing Range: 500g/100g/1000gAccuracy: 0.1/0.01/0.1
Long Nose PliersPlastic HandlesWire Cutter feature
© 2011 Sportsmoto Ltd